- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Circuit Description
The electronic control module (ECM) receives constant voltage from the batteries through the unswitched battery wires that are connected directly to the positive (+) battery post. The ECM receives switched battery input through the vehicle keyswitch wire when the vehicle keyswitch is turned ON.
Component Location
The ECM is connected to the battery by the OEM power harness through the ECM battery supply stub. This provides a constant power supply for the ECM. The location of the battery will vary with the original equipment manufacturer (OEM). Refer to the OEM service manual.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the keyswitch is in the ON position.
Conditions for Setting the Fault Codes
The ECM detects that primary ECM power supply dropped below a calibratible value while the keyswitch was in the ON position. The fault code will be active when the keyswitch is turned on following the incomplete power-down event.
Action Taken When the Fault Code is Active
The ECM records the fault code immediately when the diagnostic runs and fails.
Power-down data like trip information, maintenance monitor, and fault information will not get saved to permanent memory when the keyswitch is turned OFF.
Conditions for Clearing the Fault Code
To validate the repair, start the engine, let it idle for 1 minute, and shut it down properly. The ECM must see adequate primary ECM battery voltage when the keyswitch is turned OFF before the fault code will go inactive.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults.
Shop Talk
Possible causes of this fault code are:
Battery voltage below 6.2 VDC during cranking
High resistance in the ECM supply or return circuit
Use of a battery disconnect switch or any device that disconnects battery voltage to the ECM to turn the engine off or before the ECM is completely powered down.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
Possible Cause:
1) Loose Connection/ Terminals
2) Battery Failure
3) Fuses
4) OEM power Harness
5) ECM power harness
6) OEM harness
7) ECM calibration
Related
Categories Cumminz, DTC TRUCKS, ISX15 CM2250 (2010-12)Tags 1117, 2, 2010-12, 251, 627, CM2250, Code, Cummins, Data, Erratic, Fault, FMI, Ignition, Incorrect, Intermittent, ISX15, Lost, on-, or, PID, power, SID, SPN, Supply, with
Wiring Diagrams
Component Locators
- Noregon JPRO 2023 V3 Diagnostic Software Download 1pc
JPRO$86.00
Rated 0 out of 5
- Cat Factory Password Generator 1.0 2019 WINDOWS 10
CAT$55.00
Rated 0 out of 5
- volvo delete files 2023 33,46 GB
Trucks software$300.00
Rated 0 out of 5
- Cumminmms Insiter 8.9 Diagnostic Software
cummisznn$80.00
Rated 0 out of 5
- Cumming Caltem 5.9.1 2022 ( 1 PC )
cummisznn$78.00
Rated 0 out of 5
- Detroit BackDoor Password Generator V1 V2
Detroit$30.00
Rated 0 out of 5
- Allison DOC 2019 PC software + GEN5 2019 truck
Allison$40.00
Rated 0 out of 5
PF Diagnose$60.00
Rated 0 out of 5
Trucks software$55.00
Rated 0 out of 5
- download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi$76.00
Rated 0 out of 5
- Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software$35.00
Rated 0 out of 5
- Perkins EST 2021B v1.0 Active License + FPKG ( 1 PC )
CAT$75.00
Rated 0 out of 5
- Magic Tuner Flash Tool v2.1
Magic Tuner$180.00
Rated 0 out of 5
- Isuzu G IDSS 2020 Diagnostic Service System [08.2020] Release Full
ISUZU$125.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 108-118-128
Trucks software$38.00
Rated 0 out of 5
- CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT$45.00
Rated 0 out of 5
- Allison DOC 2021 V2 (1PC)
Allison$67.00
Rated 0 out of 5
- CAT ET Electronic Technician 2018C
CAT$45.00
Rated 0 out of 5
- CAT ET Electronic Technician 2019C
CAT$40.00
Rated 0 out of 5
- volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software$35.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT DIESEL V-71
DETROIT$38.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 230-260
DEUTZ$30.00
Rated 0 out of 5
- SERVICE MANUAL EATON UltraShift PLUS
EATON$40.00
Rated 0 out of 5
- Volvo I-Shift service manual PDF
TRUCK MANUALS$55.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 418 sms
BOBCAT$45.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 80-85-90-100-105 MK3
DEUTZ$32.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROVECTOR 26.6 – 30.7
DEUTZ$24.00
Rated 0 out of 5
- SERVICE MANUALDAF xf xe engine manual
DAF$20.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT DIESEL 16V2000 Workshop Manual M020155
DETROIT$28.00
Rated 0 out of 5
- SERVICE MANUAL EPA04 Series 60 Turbocharger Actuator Replacement
DETROIT$20.00
Rated 0 out of 5